smartctl 7.4 2023-08-01 r5530 [FreeBSD 14.0-RELEASE amd64] (local build)
Copyright (C) 2002-23, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Marvell based SanDisk SSDs
Device Model:     SanDisk SDSSDH3 1T00
Serial Number:    --
LU WWN Device Id: 5 001b44 ...
Firmware Version: 401120RL
User Capacity:    1,000,204,886,016 bytes [1.00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    Solid State Device
Form Factor:      2.5 inches
TRIM Command:     Available, deterministic, zeroed
Device is:        In smartctl database 7.3/5528
ATA Version is:   ACS-4 T13/BSR INCITS 529 revision 5
SATA Version is:  SATA 3.3, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is:    Sun May 19 14:46:01 2024    
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM level is:     128 (minimum power consumption without standby)
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]
Wt Cache Reorder: Unavailable

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00)	Offline data collection activity
					was never started.
					Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(    0) seconds.
Offline data collection
capabilities: 			 (0x11) SMART execute Offline immediate.
					No Auto Offline data collection support.
					Suspend Offline collection upon new
					command.
					No Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					No Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   2) minutes.
Extended self-test routine
recommended polling time: 	 (  10) minutes.

SMART Attributes Data Structure revision number: 4
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  5 Reallocated_Sector_Ct   -O--CK   100   100   ---    -    0
  9 Power_On_Hours          -O--CK   100   100   ---    -    7215
 12 Power_Cycle_Count       -O--CK   100   100   ---    -    1842
165 Total_Write/Erase_Count -O--CK   100   100   ---    -    189100983859
166 Min_W/E_Cycle           -O--CK   100   100   ---    -    10
167 Min_Bad_Block/Die       -O--CK   100   100   ---    -    87
168 Maximum_Erase_Cycle     -O--CK   100   100   ---    -    34
169 Total_Bad_Block         -O--CK   100   100   ---    -    698
170 Unknown_Marvell_Attr    -O--CK   100   100   ---    -    0
171 Program_Fail_Count      -O--CK   100   100   ---    -    0
172 Erase_Fail_Count        -O--CK   100   100   ---    -    0
173 Avg_Write/Erase_Count   -O--CK   100   100   ---    -    22
174 Unexpect_Power_Loss_Ct  -O--CK   100   100   ---    -    158
184 End-to-End_Error        -O--CK   100   100   ---    -    1
187 Reported_Uncorrect      -O--CK   100   100   ---    -    173
188 Command_Timeout         -O--CK   100   100   ---    -    0
194 Temperature_Celsius     -O---K   070   060   ---    -    30 (Min/Max 3/60)
199 SATA_CRC_Error          -O--CK   100   100   ---    -    0
230 Perc_Write/Erase_Count  -O--CK   003   003   ---    -    785 532 785
232 Perc_Avail_Resrvd_Space PO--CK   100   100   004    -    100
233 Total_NAND_Writes_GiB   -O--CK   100   100   ---    -    22907
234 Perc_Write/Erase_Ct_BC  -O--CK   100   100   ---    -    37742
241 Total_Writes_GiB        ----CK   253   253   ---    -    34092
242 Total_Reads_GiB         ----CK   253   253   ---    -    49966
244 Thermal_Throttle        -O--CK   000   100   ---    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01           SL  R/O      1  Summary SMART error log
0x02           SL  R/O      2  Comprehensive SMART error log
0x03       GPL     R/O      1  Ext. Comprehensive SMART error log
0x04       GPL,SL  R/O      8  Device Statistics log
0x06           SL  R/O      1  SMART self-test log
0x07       GPL     R/O      1  Extended self-test log
0x10       GPL     R/O      1  NCQ Command Error log
0x11       GPL     R/O      1  SATA Phy Event Counters log
0x24       GPL     R/O   2277  Current Device Internal Status Data log
0x25       GPL     R/O   2277  Saved Device Internal Status Data log
0x30       GPL,SL  R/O      9  IDENTIFY DEVICE data log
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xde       GPL     VS       8  Device vendor specific log

SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 173 (device log contains only the most recent 4 errors)
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 173 [0] occurred at disk power-on lifetime: 1942 hours (80 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 10 00 00 73 6c cb 10 40 00  Error: UNC at LBA = 0x736ccb10 = 1936509712

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 10 00 00 73 6c cb 10 40 00     01:32:59.453  READ FPDMA QUEUED
  60 01 00 00 08 00 00 73 6c ca 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 f0 00 00 73 6c c9 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 e8 00 00 73 6c c8 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 e0 00 00 73 6c c7 10 40 00     00:00:00.000  READ FPDMA QUEUED

Error 172 [3] occurred at disk power-on lifetime: 1942 hours (80 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 90 00 00 73 64 49 10 40 00  Error: UNC at LBA = 0x73644910 = 1935952144

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 90 00 00 73 64 49 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 88 00 00 73 64 48 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 80 00 00 73 64 47 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 78 00 00 73 64 46 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 70 00 00 73 64 45 10 40 00     00:00:00.000  READ FPDMA QUEUED

Error 171 [2] occurred at disk power-on lifetime: 1942 hours (80 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 90 00 00 73 64 49 10 40 00  Error: UNC at LBA = 0x73644910 = 1935952144

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 90 00 00 73 64 49 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 88 00 00 73 64 48 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 80 00 00 73 64 47 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 78 00 00 73 64 46 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 70 00 00 73 64 45 10 40 00     00:00:00.000  READ FPDMA QUEUED

Error 170 [1] occurred at disk power-on lifetime: 1942 hours (80 days + 22 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 41 00 90 00 00 73 64 49 10 40 00  Error: UNC at LBA = 0x73644910 = 1935952144

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  60 01 00 00 90 00 00 73 64 49 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 88 00 00 73 64 48 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 80 00 00 73 64 47 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 78 00 00 73 64 46 10 40 00     00:00:00.000  READ FPDMA QUEUED
  60 01 00 00 70 00 00 73 64 45 10 40 00     00:00:00.000  READ FPDMA QUEUED

SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged.  [To run self-tests, use: smartctl -t]

Selective Self-tests/Logging not supported

SCT Commands not supported

Device Statistics (GP Log 0x04)
Page  Offset Size        Value Flags Description
0x01  =====  =               =  ===  == General Statistics (rev 1) ==
0x01  0x008  4            1842  ---  Lifetime Power-On Resets
0x01  0x010  4            7215  ---  Power-on Hours
0x01  0x018  6     71497504864  ---  Logical Sectors Written
0x01  0x020  6       779033743  ---  Number of Write Commands
0x01  0x028  6    104788289629  ---  Logical Sectors Read
0x01  0x030  6    348928708687  ---  Number of Read Commands
0x07  =====  =               =  ===  == Solid State Device Statistics (rev 1) ==
0x07  0x008  1               2  N--  Percentage Used Endurance Indicator
                                |||_ C monitored condition met
                                ||__ D supports DSN
                                |___ N normalized value

Pending Defects log (GP Log 0x0c) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x0001  4            0  Command failed due to ICRC error
0x0002  4            0  R_ERR response for data FIS
0x0005  4            0  R_ERR response for non-data FIS
0x000a  4           12  Device-to-host register FISes sent due to a COMRESET



